Showing posts with label one. Show all posts
Showing posts with label one. Show all posts

Sunday, November 16, 2014

Battery backup converter with one NiCd cell

Battery-backupBattery-backup converter with one NiCd cell

Notebook computers and added carriageable accessories generally use a advancement array to absorb anamnesis accommodation during advancement of the capital battery. Such "bridge batteries" usually abide of bristles or six series-connected NiCd bread cells. Theyre accepted to accumulate the arrangement animate for about 5 minutes—plenty of time to bandy batteries. The ambit in Figure 1 reduces size, weight, and amount by application one NiCd corpuscle instead of bristles or six. A Saft VB4E 40-mAhr NiCd bread corpuscle has abundant accommodation to accumulate a archetypal anthology computer in append approach for about 10 minutes. All apparatus (excluding the bread cell) absorb beneath than 1/2 in.2 of pc-board area, and the amount accumulation from beneath beef advice pay for the added circuitry.

When its operational, the capital array provides ability to the systems dc/dc converters. The LT1304 addition advocate consistently monitors the dc/dc-converter ascribe via the acknowledgment affiliate absolute R3 and R4. Once the FB pin drops beneath 1.24V (corresponding to about 6V at the dc/dc-converter input), addition advocate IC1 begins switching. Accepted comes from B1, through L1, and into the SW pin on IC1. When IC1s centralized about-face turns off, the SW pin goes high, carrying accepted through D2 into the dc/dc converters ascribe capacitor, C4. C4 already exists for the dc/dc converter, so you allegation no added achievement capacitor.

The LT1304 switches at about 200 kHz; thus, L1 can be small. Switching occurs automatically as bare to authority the dc/dc converters ascribe at about 6V. Ability for IC1 is "bootstrapped" from the 5V dc/dc converters output, so it never needs to accomplish anon from the 1.2V NiCd bread cell. Should the advancement array anytime absolutely discharge, the 5V achievement drops beneath the LT1304s minimum operating voltage of 1.5V, and the absolute arrangement shuts down. At that point, the NiCd corpuscle becomes unloaded, thereby preventing overdischarge damage. Advancement operation is re-established alone afterwards the capital ability antecedent (main array or ac power) is adequate to the system.

It is generally all-important to accomplish a argumentation arresting to announce that the arrangement is accepting its ability from the advancement battery. This arresting can serve to afford amount (the advancement advocate cannot abutment abounding arrangement power) or to accessible a MOSFET about-face that prevents accepted from abounding aback into the capital battery. When the LT1304 is operating, the flyback beating present at the SW pin turns on Q1, thereby peak-charging C1 through D1. Once the voltage on pin 1 exceeds 1.17V (the LBI comparator threshold), the LBO open-collector disciplinarian is appear and pulled aerial by the resistors aural Q2.

You can affix the LBO arresting to argumentation chip or to a microcontroller input. LBO additionally turns off Q2 to attenuate charging during advancement operation. During accustomed nonbackup operation, LBO is low, befitting Q2 saturated. In this state, about 350 mA of charging accepted flows through R5 into the battery. You can calibration R5 for altered allegation currents as appropriate.

Read More..

Saturday, October 25, 2014

Class one Headphone Amplifier

This Class one Headphone Amplifier circuit is derived from the Portable Headphone Amplifier featuring an NPN/PNP compound pair emitter follower output stage. An improved output driving capability is gained by making this a push-pull Class-A arrangement. Output power can reach 427mW RMS into a 32 Ohm load at a fixed standing current of 100mA. The single voltage gain stage allows the easy implementation of a shunt-feedback circuitry giving excellent frequency stability.
.
Circuit diagram :
Class-A Headphone Amplifier-Circuit Diagram
Class-A Headphone Amplifier Circuit diagram

The above mentioned shunt-feedback configuration also allows the easy addition of frequency dependent networks in order to obtain an useful, unobtrusive, switchable Tilt control (optional). When SW1 is set in the first position a gentle, shelving bass lift and treble cut is obtained. The central position of SW1 allows a flat frequency response, whereas the third position of this switch enables a shelving treble lift and bass cut.
.
Note:
  • Before setting quiescent current rotate the volume control P1 to the minimum, Trimmer R6 to zero resistance and Trimmer R3 to about the middle of its travel.
  • Connect a suitable headphone set or, better, a 33 Ohm 1/2W resistor to the amplifier output.
  • Connect a Multimeter, set to measure about 10Vdc fsd, across the positive end of C5 and the negative ground.
  • Switch on the supply and rotate R3 in order to read about 7.7-7.8V on the Multimeter display.
  • Switch off the supply, disconnect the Multimeter and reconnect it, set to measure at least 200mA fsd, in series to the positive supply of the amplifier.
  • Switch on the supply and rotate R6 slowly until a reading of about 100mA is displayed.
  • Check again the voltage at the positive end of C5 and readjust R3 if necessary.
  • Wait about 15 minutes, watch if the current is varying and readjust if necessary.
Parts List :
.
P1          : 22K  Dual gang Log Potentiometer 
R1 : 15K
R2 : 220K
R3 : 100K
R4 : 33K
R5 : 68K
R6 : 50K
R7 : 10K
R8,R9 : 47K
R10,R11 : 2R2
R12 : 4K7
R13 : 4R7
R14 : 1K2
R15,R18 : 330K
R16 : 680K
R17,R19 : 220K
R20,R21 : 22K
C1,C2,C3,C4 : 10µF/25V
C5,C7 : 220µF/25V
C6,C11 : 100nF
C8 : 2200µF/25V
C9,C12 : 1nF
C10 : 470pF
C13 : 15nF
D1 : LED
D2,D3 : 1N4002
Q1,Q2 : BC550C
Q3 : BC560C
Q4 : BD136
Q5 : BD135
IC1 : 7815
T1 : 15CT/5VA Mains transformer
SW1 : 4 poles 3 ways rotary Switch
SW2 : SPST slide or toggle Switch
 

Read More..

Monday, October 20, 2014

Capacitor and Resistor in One Switch Box

It would be nice and comfortable doing our work and what we needed are readily available to save time and effort. It lessens the hassle of looking for missing pieces or even using multiple devices to check the accuracy and effectiveness of the equipments we are using.

pacitor and Resistor in One Switch Box
Just like this switch box that has a capacitor and resistor in one unit. It will be easier and faster to check the capacitance and resistance by switching the knobs. This device may look old-fashioned but can really come very handy. This is simple and not that expensive to make and very useful in electronic projects or for the purpose of collecting devices for future use.

pacitor and Resistor in One Switch Box



Source : extreamcirciuts
Read More..