Monday, November 3, 2014

OPERATIONAL AMPLIFIER OP AMP OSCILLATOR ELECTRONIC CIRCUIT

OPERATIONAL AMPLIFIER OP-AMP OSCILLATOR ELECTRONIC CIRCUIT

Timing capacitor (C1) produces several times constants which is used to allow large voltage swings on the input due to the LM101s large input voltage range. The R2 should be reduced and the C1 should be increased to keep from exceeding these ratings. The smaller polarized capacitors is still used by returning them to positive supply voltage instead of ground, even though C1 requires the large values.
Read More..

Sunday, November 2, 2014

gigabyte motherboard GA H55M S2H

Intel® H55 Chipset
Innovative Smart 6 technology for smarter PC management
Supports Intel Core™ i7/ Core™ i5/ Core™ i3 LGA1156 processors
Dynamic Energy Saver™ 2 technology enables best energy efficiency
2 PCI-E 2.0 x16 graphics interface(x16+x4) with ATI CrossFireX support for ultimate graphics performance
AutoGreen technology Greening your PC via Bluetooth cellphone
Patented DualBIOS™ technology delivering highest level failure protection
Easy BIOS setting for GPU overclocking
Supports 6 devices without the need for drivers to be installed before being fully operational
Enhanced Intel HD Graphics integrated with the processor
Integrated HDMI/ DVI interface for smoother HD video playback
Compatible with Windows 7 to deliver the best
operation experience
Meet European Union ErP(Energy-related Products) requirement
Read More..

3V DC to 5V DC REGULATED POWER SUPPLY ELECTRONIC DIAGRAM


3V DC to 5V DC REGULATED POWER SUPPLY ELECTRONIC DIAGRAM

A 5V DC regulated output from 2 cells 3V DC batteries. The output current of the circuit is limited to 50mA. However, it still able to supply many microcontroller circuits. 3009 and 560R Resistor provide the 5V DC output, make up a voltage divider network.
Read More..

12 V AUDIO AMPLIVIER IC TDA7222AP ELECTRONIC DIAGRAM

12 V AUDIO AMPLIVIER IC TDA7222AP ELECTRONIC DIAGRAM

Use 12V DC for powering the circuit. The IC must be heatsinked. Speaker can be a 4 ohms one.For optimum performance input and output must be separately grounded.

Pin Name Description
1 Vcc Supply Voltage
2 RR Ripple Reject
3 MC Muting control
4 OP AF Signal Input
5 FB FB Filter
6 GA Gain adjust
7 GND Ground
8 GND Ground
9 OP AF Output
10 BS BootStrap
Read More..

Fire Sensor Pyroelectric Circuit Diagram

This is the  Fire Sensor Pyroelectric Circuit Diagram. Here is an ultra-sensitive fire sensor that exploits the direct piezoelectric  property  of  an ordinary piezo element to detect fire. The lead  zirconate  titanate  crystals  in the piezo element has a property to de-form and generate an electric potential plifier with gate protected p-channel.  MOSFETs in the inputs. It has high speed  of  performance  and  low  input current requirements. There are two inputs—the non inverting input (pin 3) connected to the piezo element through diode D7 (OA71) that carries the volt-age signal from the piezo element and the inverting input (pin 2) that gets a momentarily changes the voltage level at pin 3 of IC1 and its output swings high. Transistor T1 conducts taking the reset pin 12 of IC2 to ground. IC2 is now enabled and start oscillating. With the shown values of the oscillating components C3 (0.22) and R8 (1M), when heated, thus converting the piezo element into a heat sensor. 

Pyroelectric
Pyroelectric Fire Sensor -Circuit-Diagram
 
The circuit we  have  described  here  is  very  sensitive. It gives a warning alarm if the room temperature increases more than 10 degree Celsius. The entire circuit is divided  into  two  section—the  sensor and the power supply section. Sensor side circuit. Fig. 1 shows the fire sensor circuit. The front end of the circuit has a sensitive signal amplifier built around IC1 (CA3130). It gives a  high  output when the  temperature near the piezo element increases. IC CA 3130 is a CMOS operational am-preset  volt-age through VR1.By adjusting VR1, it is easy  to set the reference voltage level at pin 2. In normal condition, IC1 gives a low output and the remaining circuitry will be in a standby state. Capacitor C2(10P) keeps the non-inverting in-put of IC1 stable, so that even a slight change in voltage  level  in  the  inputs can change the output to high. 

Normally, IC1 gives a low output, keeping transistor T1 non-conducting. Reseting pin 12 of IC2 (CD4060) connected to the collector of transistor T1 gets a high voltage through R6 and IC2 remains disabled. When the piezo element gets heat from fire, asymmetry in its crystals cause a potential change, enabling capacitor C2 to discharge. It the first output (Q3) turns high after 4 seconds and a red LED starts flashing. If the heat near the piezo persists, Q7 (pin 14) output of IC2 becomes high after  1  minute,  and  the  alarm  starts beeping. If heat continues, Q9 (pin15) turns high after four minutes and turns on the relay driver transistor T2. At the same time, diode D8 conducts and IC2 stops oscillating and toggles.The  solenoid  pump  connected  to the N/O (normally opened) contact of the relay starts spraying the fire-ceasing foam or water to the possible sites of fire.

Power Power Supply With Battery Backup  Circuit Diagram

Power  supply  circuit. Power sup-ply section (Fig. 2) comprises a 0-12V, 1 A step down transformer with a standard full wave rectifier formed by D1 through D4 and filter capacitor C1. A battery backup is provided if the mains supply cut-off due to short-circuit and fire. A 12V, 4.5 Ah rechargeable battery is used for backup to give sufficient current to the solenoid pump. 

When mains power is available, diode D5 forward biases. It provides power to the  circuit  and  also  charges  the  bat-tery through resistor R2 and it limits the charging current to 120 mA. When power fails, diode D5 reverse biases and diode D6 forward biases, giving instant backup to the circuit. LED1 indicates  the  availability  of  mains power.Assemble the circuit on a common PCB and enclose it in a suitable case. Connect the piezo element to the circuit using thin plastic wire. Glue the flat side of the piezo element on a 30x30 cm aluminium sheet to increase its sensitivity. Fix the sheet with the piezo  sensor  to  the  site  where  protection is needed. The remaining circuit can be fixed in a suitable place. If only the alarm generator is needed, omit the relay driver section. 



Author :D. Mohan Kumar - Copyright : EFYMag
Read More..

Saturday, November 1, 2014

TDA2040 Car stereo amplifier Diagram Circuit


Car Audio Amplifier Circuit:

Given below is a car stereo amplifier circuit using audio amplifier IC – TDA2040

Description of the circuit:

A car stereo amplifier circuit using TDA2040 is shown here. TDA2040 is a monolithic integrated audio amplifier that operates in Class AB mode. The IC has built in circuitry for short circuit protection and thermal shut down and more over it can be operated from a single supply too. The amplifier can deliver 12 watts into to a 8 ohm speaker.

In the circuit the IC is wired in order to operate from the cars 12V line. Capacitor C7 is the input DC decoupling capacitor and R4 provides feedback. Network consisting of resistor R5 and capacitor C5 provides high frequency stability and prevents any chance of oscillation. Capacitor C6 couples the ICs output to the speaker. C2 and C1 are power supply filters.

Circuit diagram of car stereo circuit using TDA2040


Car amplifier circuit diagram

Notes.

  • Quality of the PCB is a very crucial factor in the amplifiers performance.
  • The amplifier can be operated from cars 12V line.
  • Heat sink is necessary for TDA2040.
  • All electrolytic capacitors must be rated 15V.
  • Only one channel is shown here. For stereo application you must make one more identical copy. 
Read More..

General DC Power Supply with uA723 This is the power supply circuit for general purpose usage General Power Supply with uA723 circuit diagram The s

General DC Power Supply with uA723

This is the power supply circuit for general purpose usage.
General


The supply can be used for supply output voltages from 1 to 35V. The line transformer should be selected to give about 1.4 times the desired output voltage from the positif side of filted capacitor C1 to ground. Potensiometer R2 sets the output voltage to the desired value by adjusting the reference input. Rsc is the current limit set resistor.

For example, if the maximum current output is to be 1A, Rsc=0.65/1.0 = 0.65 Ohm. The 1KOhm resistor,R5, is a light-loaded resistor designed to improve the no-load stability of the supply.
Read More..