Tuesday, October 28, 2014

IC TDA7294 50W Power Amplifier with Diagram Circuit


This is a great audio amplifier circuit based on single power IC TDA7294. TDA7294 is intended for use as a high quality audio class AB amplifier in hi-fi applications. It has very low noise and distortion, wide bandwidth and good output current capability, enabling it to supply high power into both 4Ω and 8Ω loads. It has both short circuit and thermal protection, so is quite robust.


Component part list:

R1_____________ 150R R2, R3, R5_____ 10K R4_____________ 680R R6_____________ 22K IC1____________ TDA 7294 Heatsink
C1____________ 1u5F or 1u C2____________ 2n7F C3, C6________ 22uF 63V C4, C5________ 10uF 63V C7, C9________ 2200uF 50V C8, C10_______ 100nF

With the addition of a handful of parts and a suitable power supply, this module will deliver over 50W RMS into 4 or 8 ohms with <0.1% total harmonic distortion (thd) and <0.1% intermodulation distortion (imd). a similar circuit was published in elektor magazine, 11/96.

It is also suitable as a replacement power amp stage, or upgrade for many existing amplifiers of between 30W-50W, provided they have a suitable dual supply, and most do.

Read More..

Stabilised zener voltage


Currently approximately primarily-rate voltage references are offered. Take the LM385 instead of pattern: this is available for dissimilar voltages and even comes now an modifiable version. pardon? is supplementary, the current consumption can be alive set aside very petite (10 µA). But like often happens, you may not give birth to individual to worker once you need one meant for an experimental circuit. In with the intention of state of affairs, you possibly will draw on an ordinary zener diode for the reference. Unfortunately, they have a somewhat advanced inside resistance (all but 5 ?), which agency they won’t befall very fixed once the supply voltage varies. The solution is exact in the field of front of us: use the stabilised zener voltage at the same time as the supply voltage! This is clearly single workable if the stabilised voltage is top than the zener voltage.

Stabilised
Stabilised zener voltage
It therefore has to be alive improved a insufficiently. This is exactly could you repeat that? this circuit does: it amplifies it by a aspect of two. The current limiting resister must be chosen such to facilitate a current of 1 to 3 mA flows through the zener diode. Manufacturers ordinarily state the zener voltage next to a current relating 3 to 5 mA. The zener diode is fed from a stabilised voltage and for this reason has a very durable operating indicate, which is objective from the supply voltage. The graph speaks instead of itself. It is cloudless to the output voltage is much supplementary stable. The graphs exhibit been plotted to numerous scales to form the comparison easier. all the rage veracity the opamp output is twice the zener voltage. Zener diodes moreover have a warmth coefficient, which is smallest on behalf of types with a zener voltage around 5 volts. to all intents and purposes whichever type of opamp must stay proper; even our old associate the 741 workings well as much as necessary.
Read More..

Ballast and Starter Fluorescent Lamp

Installation of fluorescent lamp circuits, we can see that most of the foot fluorescent lamp mounted in series with the ballast and partly installed pareral the starter.

Ballast
Ballast resistor is basically a coil (choke coil) is an iron core. Fluorescent lamp ballasts in the works:
  •     Provide the initial installation of the electrodes in order to provide free electrons in large numbers
  •     Provide a potential wave big enough to hold a spark between two electrodes
  •     Preventing the occurrence of an increased flow of sparks that exceeds a certain limit for each lamp size.
Besides ballast serves to reduce the influence of the changes that interfere with the movement of light (stroboscopic) and reduce the loss side (auxiliary losses). Therefore, each fluorescent lamp ballast has always had a planned to power, voltage, and frequency are adjusted to the light TLnya respectively.

Starter
Starter on a fluorescent lamp consists of a small glass balloon filled with noble gases. Inside the bubble there are two metal electrodes as dual filament. The distance between the two electrodes are arranged with a certain distance so that the starter will turn on voltage of 100-200 V. Starter switch serves as the delay time (time delay switch) are connected in parallel with two-foot fluorescent lamp.

When the fluorescent lamp is connected to the voltage of tissues, then in a short time starter filament is connected (on) and then decide again if the lamp has been lit with a stable NE. At the time of the filament is connected, a large current will flow through the ballast from the power grid, then to the lamp electrodes, wire electrodes and the other starter, for subsequent return to the network. The existence of these currents will make the incandescent lamp electrodes and removing electrons.

Meanwhile, the voltage at the starter has been lost, so that the starter went out and become cool. Both dual metal electrodes in the starter going straight back and decided that the current is flowing. Because of the sudden termination of this, the ballast will be raised an electromotive force is quite high. Shock voltage is in series with line voltage. When raised at the right time, the voltage at the two filament lamps TL will be high enough to ignite the filament-provided tube filaments are hot enough.

In the first cycle of the tube is not already on the events as described above will be repeated, until the tube lights up. After the fluorescent lamp is lit, the starter will be parallel with the lamp. Therefore, the voltage on the lamp voltage is lower than the starter, the starter will remain extinguished.

To reduce the spark at the spark electrode bi-metal can be mounted a small capacitor in parallel with the starter. Installation of condenser is also able to improve the termination of the current in the starter and reduce radio interference.
Read More..

Surround Sound Installation Tips


With the increasing popularity of HDTV, watching a DVD show next to home is a exalted entertainment experience. The picture is pointed, exonerate, and vivid. But could you repeat that? on the sound? gone all, to is single of the real attractions of up for grabs to a show acting, the wraparound sound so as to lets you hear all delegate. So is here a way to bring that kind of audio into our homes too? agreed!

In reality surround sound has been around in support of a while at this instant fashionable individual form or else a new, but it precisely in no way had a platform to bring it into the mainstream more willingly than HDTV and digital media like the DVD became so prevalent. But now by combining the totally equipment, a person can truly very compactly simulate the picture the stage experience right in the comfort of their to your house when they famine.

On behalf of surround sound, you desire need three things, (1) a digital source to facilitate has surround sound already encoded into it such what a DVD or else a HDTV broadcast, (2) equipment to decode to facilitate surround sound hint, and (3) on smallest amount 6 speakers with a subwoofer to take rotund improvement of the generally standard 5.1 surround sound format. Its called 5.1 as it avail yourself of 5 channels of sound to drive 5 separate speakers, and the .1 stands in favor of the low-frequency subwoofer.

When you tolerate the equipment you need to ascertain a surround sound setup with the aim of choice exist justification for your house. Much of the sitting room area will be single-minded by the size and type of box with the intention of you have. If it is a 40" HDTV, which is a very everyday size, you can probably sit re 5-8 feet away and not notice a few degradation all the rage the picture quality. simply conduct experiment with the seats distance until it seems comfortable though. subsequently the two front speakers regularly flank the box, but meet constant to they are ample adequate to form a triangle with the seats area so one and all wish be present in the sound agreeable see.

The two back speakers are often placed somewhere around the sitting room area and faced either to a part otherwise rear barrier. The halfway point narrator needs to be situated somewhere close to the tube, and the subwoofer can come about position anywhere into the extent with the intention of you like, since it puts vetoed such low frequency low that seems to arrive from all over the place.

All opportunity has sundry listening characteristics though due to its configuration and furnishings, so feel boundless to carry out trial around until you stumble on the combination so as to moving parts unsurpassed instead of you. A surround sound installation may perhaps seem challenging, but its impartial simply getting the entitlement equipment and introduction the speakers everyplace they be the source of the finest overall sound.

Thad Pickering writes on many consumer allied topics plus audio and tape. You can get prevented supplementary in the region of surround sound setup and surround sound installation by visiting our to your house the stage website.

Read More..

Monday, October 27, 2014

Infrared Audio Transmitter

Infrared Audio Transmitter
Using this low cost Project individual can produce AUDIO from tube with no worrying a person. It does not application some wire relating television and headset. all the rage place of couple of wires it uses imaginary Infrared light to transmit audio signals from small screen to earphone. lacking using several lens a range of up to 6 meters is promising. Range can survive extended by using Lenses and Reflectors with IR sensors comprising transmitters and receivers. IR transmitter uses two-stage transistor amplifier to drive two IR leds connected dressed in succession. An audio output transformer is used (in reverse) to pair Audio output from television to the IR transmitter.
Read More..

Different types of TV TUNER

TV tuner that is used on older models and new models of television there are some differences. Therefore, understanding the different types of tuner would be useful if we want to replace the tuner with the other models.


Supply voltage tuner.
Tuner older models generally use a supply voltage of 12v, the new models are commonly used 5V supply voltage. Some use a 9V voltage, but very rare.

TV TUNER
Voltage Synthesizer tuner (VS tuner)
Tuner that uses a tuning control (VT or BT) with a voltage between 0 to 33V Voltage Synthesizer tuner named. TV can be found on the aircraft models, old and new
Based on how the control band-switch, Tuner VS then there are 2 kinds, namely
Using 3-Band input sw, the VL-VH-U
Using 2-Band input sw, the Band SW1 and SW2 Band. This tuner is actually similar to the type of band 3-sw. For control-sw 2 band is in the tuner will still be converted into 3-sw bands.

Frequency Synthesizer tuner (FS tuner) or the type of PLL
Tuner wherein the tuning voltage and the voltage controlled band switching the digital communication through SDA and SCL. This tuner has a supply voltage Vcc, which is
5V is used for the digital tuner circuit control and
33V (fixed voltage or fixed) is used to control the voltage supplied to the tuning in the digital circuits within the tuner.
(Tuner old) sometimes there are additional circuit voltage of 12V to the tuner.

Frequency band.
Based on the wide range of revenue-frequency band, there are three kinds of tuner
Normal tuner
Superband tuner
Tuner hyperband

Normal tuner, the tuner that can receive broadcasts "on-air" (terrestrial) TV in the frequency band:
  • Frequency of VHF Band I - VL 41-68 Mhz
  • Band III - VH 174-230 Mhz
  • Frequency UHF Band IV - U 470-581 Mhz
  • Band V - U 582-960 Mhz
  • Band II 87.5 - 104 MHz is used for FM radio broadcasting
  • VL and VH bands used for broadcast channels 2 through 12
  • U bands used for broadcast channels 21 to 69
Superband Tuner and Hyperband, the tuner can receive broadcast as normal tuner plus the ability to receive broadcasts "off air" CATV (cable television).
  • S band using frequency band between VL and VH
  • H-band using a frequency band between VH and U
  • Superband Tuner can receive the broadcast band S
  • Hyperband tuner can receive broadcast band and S band H
Based on the IF frequency out
IF frequency tuner out there who have 38/38.9/45.75 Mhz frequency. In Indonesia generally use 38.9Mhz frequency, but sometimes there is a use 38.0Mhz


Based on the pin-out
There are several kinds of tuner long pin-out configuration. But now almost all the tuner is already using an international standard 11-pin

Universal tuner
China is now producing "universal tuner" 11-pin. Indonesia was just the market we do not know whether it exists or not. This tuner can be used to substitute for the various types of tuners and tuner can adjust to this direct voltage of 5, 9, or 12v.

RF antenna input connector
Form the antenna input connector there are two kinds, namely:
  • RCA type connectors
  • Antenna RF connector
Tuner modules
Tuner is a tuner module inside there are all Video IF amplifier circuit and the FM-detector. This kind of tuner is using VS and some are using the FS.
Tuner module has output like:
  • RF AGC-out
  • RF AFC-out
  • Audio-out
  • Video-out
  • Base band out, the signal to be processed into stereo sound circuit.
Except that in tuner is also sometimes diperlengkapa with audio-switch to TV / AV-in. Therefore, to the sound of the AV-in connected via Audio-in found on the tuner module. Sometimes the sound volume to be controlled in the tuner module.
  • SONY tuner module 1
  • SONY tuner module 2
  • Toshiba tuner module
Impedance input / output
Impedance tuner has all kinds of input / output 75 ohm.

How to distinguish 2-band tuners VS sw with PLL tuner FS
In all these circumstances and the removable pin 11 feet was not cut, it is sometimes difficult to distinguish between two band-tuner tuner sw with FS.
Some models have a tuner pin legs partially emptied. FS Tuner has a location pin 30V voltage 3 numbers from the back (of the IF pin out).
Read More..

STK433 730 E 60 watt stereo power audio amplifier circuit and explantion

A very simple high efficiency 60 watt stereo power audio amplifier circuit can be designed using the STK433-730-E hybrid IC designed to be used in class AB audio power amplifiers.

This class AB audio stereo power amplifier circuit will provide an output power of 30 watt on two channels at a 6 ohms load . Also this AB audio power amplifier circuit supports a 4 ohms load . For maximum rating on a 6 ohms load this stereo power amplifier project must be powered from a dual 28 volt very good filtered DC power source . For maximum rating on a 4 ohms load this 60 watt stereo power amplifier must be powered from a dual 25 volt DC power source , but typically is recommended a dual 18 volts DC power source on a 4 ohms load .
If is used to provide maximum ratings the output power will have a maximum 10% THD .
Exceeding the maximum ratings, even momentarily, may cause damage to the hybrid IC.
Use the hybrid IC so that the voltage applied to the stand-by pin (pin 13) never exceeds the maximum rating. The power amplifier is turned on by applying +2.5V to +5.5V to the stand-by pin (pin 13).

An output limiting circuit for substrate overheating is incorporated to protect the hybrid IC from the heat generation exceeding the maximum rating.
The load short-circuit protection circuit is activated when it has detected an overcurrent in the output transistors.
However a thermoplastic adhesive resin is used to secure the case and aluminum substrate.
When the IC supply voltage, VCC, is .18V and RL is 4 , the total power dissipation, Pd, within the hybrid IC, will be a maximum of 33Wat 1kHz for a continuous sine wave signal according to the Pd-PO characteristics.
STK433-730-E
Therefore, the value of 3.10.C/W, is the required thermal resistance of the heat sink.
Read More..