Showing posts with label voltage. Show all posts
Showing posts with label voltage. Show all posts

Thursday, November 13, 2014

7805 Voltage Regulator Circuit

A voltage regulator is used to produce a constant linear output voltage. It’s generally used with AC to DC power supply. And also it can be used as well as a DC to DC voltage converter . To regulating low voltage, most used device is one single IC. 7805, 7812, 7905 etc. 78xx series are design for positive and 79xx series are for Negative voltage regulator.

7805 is a three terminal +5v voltage regulator IC from 78XX chips family. See 7805 pinout below. LM78XX series are from National Semiconductor. They are linear positive voltage regulator IC; used to produce a fixed linear stable output voltage.  National Semiconductor has also negative voltage regulator chips family, they indicate with LM 79XX. 78xx is used more than 79xx because negative voltage has a few usability purposes as we see.
I was previously posted a 5v regulated power supply circuit using 7805 IC, that circuit and this 7805 voltage regulator circuit is almost the same.


Circuit diagram of 7805 Voltage Regulator


Fig: 7805 Voltage Regulator Circuit



7805 pinout


Fig: Pinout of 7805

Its output voltage is +5V DC that we need. You can supply any voltage in input; the output voltage will be always regulated +5V. But my recommendation is, don’t supply more than 18V or less than 8V in input. There used two capacitors in this voltage regulator circuit, they aren’t mandatory to use. But it will be best if you use them. They helped to produce a smooth regulated voltage at output. Use electrolyte capacitor instead of ceramic capacitor.

One limitation of 7805 I have found that is its output current 1A maximum. Otherwise it is a good voltage regulator if you are happy with 1A. But if   you need over 400mA current in output then you should use a Heat Sink with IC LM7805. Otherwise it may fall damage for overheating.
Read More..

Friday, November 7, 2014

Mini High Voltage Generator Circuit

Here’s a project that could be useful this summer on the beach, to stop anyone touching your things left on your beach towel while you’ve gone swimming; you might equally well use it at the office or workshop when you go back to work. In a very small space, and powered by simple primary cells or rechargeable batteries, the proposed circuit generates a low-energy, high voltage of the order of around 200 to 400 V, harmless to humans, of course, but still able to give a quite nasty ‘poke’ to anyone who touches it.

Quite apart from this practical aspect, this project will also prove instructional for younger hobbyists, enabling them to discover a circuit that all the ‘oldies’ who’ve worked in radio, and having enjoyed valve technology in particular, are bound to be familiar with. As the circuit diagram shows, the project is extremely simple, as it contains only a single active element, and then it’s only a fairly ordinary transistor. As shown here, it operates as a low-frequency oscillator, making it possible to convert the battery’s DC voltage into an AC voltage that can be stepped up via the transformer.

Using a centre-tapped transformer as here makes it possible to build a ‘Hartley’ oscillator around transistor T1, which as we have indicated above was used a great deal in radio in that distant era when valves reigned supreme and these was no sign of silicon taking over and turning most electronics into ‘solid state’. The ‘Hartley’ is one of a number of L-C oscillator designs that made it to eternal fame and was named after its invertor, Ralph V.L Hartley (1888-1970). For such an oscillator to work and produce a proper sinewave output, the position of the intermediate tap on the winding used had to be carefully chosen to ensure the proper step-down (voltage reduction) ratio.

Here the step-down is obtained inductively. Here, optimum inductive tapping is not possible since we are using a standard, off-the-shelf transformer. However we’re in luck — as its position in the centre of the winding creates too much feedback, it ensures that the oscillator will always start reliably. However, the excess feedback means that it doesn’t generate sinewaves; indeed, far from it. But that’s not important for this sort of application, and the transformer copes very well with it.

The output voltage may be used directly, via the two current-limiting resistors R2 an R3, which must not under any circum-stances be omitted or modified, as they are what make the circuit safe. You will then get around 200 V peak-to-peak, which is already quite unpleasant to touch. But you can also use a voltage doubler, shown at the bottom right of the figure, which will then produce around 300 V, even more unpleasant to touch. Here too of course, the resistors, now know as R4 and R5, must always be present. The circuit only consumes around a few tens of mA, regardless of whether it is ‘warding off’ someone or not! If you have to use it for long periods, we would however recommend powering it from AAA size Ni-MH batteries in groups of ten in a suitable holder, in order not to ruin you buying dry batteries.

Circuit diagram:
mini-high-voltage-generator-circuit

Warning!
If you build the version without the voltage doubler and measure the output voltage with your multimeter, you’ll see a lower value than stated. This is due to the fact that the waveform is a long way from being a sinewave, and multimeters have trouble interpreting its RMS (root-mean-square) value. However, if you have access to an oscilloscope capable of handling a few hundred volts on its input, you’ll be able to see the true values as stated. If you’re still not convinced, all you need do is touch the output terminals...

To use this project to protect the handle of your beach bag or your attachecase, for example, all you need do is fix to this two small metallic areas, quite close together, each connected to one output terminal of the circuit. Arrange them in such a way that unwanted hands are bound to touch both of them together; the result is guaranteed! Just take care to avoid getting caught in your own trap when you take your bag to turn the circuit off!
Read More..

Wednesday, October 29, 2014

LM331 Frequency to voltage converter Diagram Circuit

Description.
LM331 is basically a precision voltage to frequency converter from National Semiconductors. The IC has a hand full of applications like analog to digital conversion, long term integration, voltage to frequency conversion, frequency to voltage conversion. Wide dynamic range and excellent linearity makes the IC well suitable for the applications mentioned above.
Here the LM331 is wired as a frequency to voltage converter which converts the input frequency into a proportional voltage which is extremely linear to the input frequency. The frequency to voltage conversion is attained by differentiating the input frequency using capacitor C3 and resistor R7 and feeding the resultant pulse train to the pin6 (threshold) of the IC. The negative going edge of the resultant pulse train at pin6 makes the built-in comparator circuit to trigger the timer circuit. At any instant, the current flowing out of the current output pin (pin 6) will be proportional to the input frequency and value of the timing components (R1 and C1). As a result a voltage (Vout) proportional to the input frequency (Fin) will be available across the load resistor R4.
Circuit diagram.
Notes.
  • The circuit can be assembled on a vero board.
  • I used 15V DC as the supply voltage (+Vs) while testing the circuit.
  • The LM331 can be operated from anything between 5 to 30V DC.
  • The value of R3 depends on the supply voltage and the equation is R3= (Vs – 2V)/ (2mA).
  • According to the equation, for Vs = 15V, R3=68K.
  • The output voltage depends on the equation, Vout = ((R4)/(R5+R6))*R1C1*2.09V*Fin.
  • POT R6 can be used for calibrating the circuit.
Read More..

Tuesday, October 28, 2014

Stabilised zener voltage


Currently approximately primarily-rate voltage references are offered. Take the LM385 instead of pattern: this is available for dissimilar voltages and even comes now an modifiable version. pardon? is supplementary, the current consumption can be alive set aside very petite (10 µA). But like often happens, you may not give birth to individual to worker once you need one meant for an experimental circuit. In with the intention of state of affairs, you possibly will draw on an ordinary zener diode for the reference. Unfortunately, they have a somewhat advanced inside resistance (all but 5 ?), which agency they won’t befall very fixed once the supply voltage varies. The solution is exact in the field of front of us: use the stabilised zener voltage at the same time as the supply voltage! This is clearly single workable if the stabilised voltage is top than the zener voltage.

Stabilised
Stabilised zener voltage
It therefore has to be alive improved a insufficiently. This is exactly could you repeat that? this circuit does: it amplifies it by a aspect of two. The current limiting resister must be chosen such to facilitate a current of 1 to 3 mA flows through the zener diode. Manufacturers ordinarily state the zener voltage next to a current relating 3 to 5 mA. The zener diode is fed from a stabilised voltage and for this reason has a very durable operating indicate, which is objective from the supply voltage. The graph speaks instead of itself. It is cloudless to the output voltage is much supplementary stable. The graphs exhibit been plotted to numerous scales to form the comparison easier. all the rage veracity the opamp output is twice the zener voltage. Zener diodes moreover have a warmth coefficient, which is smallest on behalf of types with a zener voltage around 5 volts. to all intents and purposes whichever type of opamp must stay proper; even our old associate the 741 workings well as much as necessary.
Read More..

Thursday, October 23, 2014

Car Voltage Gauge

The Car Voltage Gauge is based on 3 parts. The input circuit is an Analog to Digital Converter (IC2 CA3162E). The purpose of this chip is to sample an analog voltage and convert it to a decimal value which is read by a Display/Decoder Driver (IC1 CA3161E). This chip will turn each seven segment display on through the driver transistor Q1 - Q3. The power is derived from the car and is converted to 5 volts by the 5 volt regulator. The circuit works as follows: The 10uf capacitor is charged up by the cars voltage. Its value is then read by IC2 and a decimal value of that voltage is provided to IC1 which multiplexes the three display units.

Car Voltage Gauge circuit diagram

Each display is turned on sequentially with its appropriate value displayed. The transistors Q1 through Q3 control the drive to each seven segment display. By monitoring the cars voltage with an accurate multimeter you can adjust the "Zero Adj." pot and the "Gain Adj." pot for accurate readings. LED 1 and 2 are optional. They can be used to indicate power on or can light up a cut out display that says "Volts". This can be made by a plastic module that has a thin plastic cover on it with the word "Volts" cut into it. The LEDs would be mounted inside the module. 
 
 
Source by : extreamcirciuts.net
Read More..

Friday, September 26, 2014

Voltage Tester for Model Batteries

With a suitable load, the terminal voltage of a NiCd or lithium-ion battery is proportional to the amount of stored energy. This relationship, which is linear over a wide range, can be used to build a simple battery capacity meter. 

Circuit Image :
 Voltage Tester for Model Batteries Image
Voltage Tester for Model Batteries Circuit Image 

This model battery tester has two functions: it provides a load for the battery, and at the same time it measures the terminal voltage. In addition, both functions can be switched on or off via a model remote-control receiver, to avoid draining the battery when it is not necessary to make a measurement. The load network, which consists of a BC517 Darlington transistor (T2) and load resistor R11 (15 Ω /5 W), is readily evident. When the load is active, the base of T1 lies practically at ground level. Consequently, T1 conducts and allows one of the LEDs to be illuminated. 

Circuit Diagram :
Voltage Tester for Model Batteries-Circuit Diagram
Voltage Tester for Model Batteries Circuit Diagram

The thoroughly familiar voltmeter circuit, which is based on the LM3914 LED driver, determines which LED is lit. The values of R6 and R7 depend on the type and number of cells in the battery. The objective here is not to measure the entire voltage range from 0 V, but rather to display the portion of the range between the fully charged voltage and the fully discharged voltage. Since a total of ten LEDs are used, the display is very precise. For a NiCd battery with four cells, the scale runs from 4.8 V to 5.5 V when R6 = R7 = 2 kΩ. The measurement scale for a lithium-ion battery with two cells ranges from 7.2 V to 8.0 V if R6 = 2 kΩ and R7 = 1 kΩ. 

For remote-control operation, both jumpers should be placed in the upper position (between pin 1 and the middle pin). In this configuration, either a positive or negative signal edge will start the measurement process. A positive edge triggers IC1a, whose output goes High and triggers IC1b. A negative edge has no effect on IC1a, but it triggers IC1b directly. In any case, the load will be activated for the duration of the pulse from monostable IC1b. Use P12 to set the pulse width of IC1a to an adequate value, taking care that it is shorter than the pulse width of IC1b. 

If the voltage tester is fitted into a remote-controlled model, you can replace the jumpers with simple wire bridges. However, if you want to use it for other purposes, such as measuring the amount of charge left in a video camera battery, it is recommended to connect double-throw push-button switches in place of JP1 and JP2. The normally closed contact corresponds to the upper jumper position,while the normally open contact corresponds to the lower position.

Parts :
Resistors:
R1,R2 = 47kΩ
R3 = 100kΩ
R4 = 500kΩ
R5 = 1kΩ
R6,R7 = see text (1% resistors!)
R8 = 1kΩ5
R9 = 1kΩ2
R10 = 330Ω
R11 = 15Ω 5W
R12 = 15kΩ
P1 = 100kΩ preset
Capacitors:
C1 = 10nF
C2 = 100nF
Semiconductors:
D1-D10 = LED, red, high effi-ciency
T1 = BC557
T2 = BC517
IC1 = 74HC123
IC2 = LM3914AN
Miscellaneous:
PC1,PC2,PC3 = solder pin
JP1,JP2 = jumper or pushbutton

PCB Layout :
B. PCB Laout
Voltage Tester for Model Batteries PCB Layout


Copyright : Elektor
Read More..

Thursday, September 25, 2014

Voltage Controlled Oscillator Circuit

A simple voltage controlled oscillator circuit which produces both triangular and square wave outputs is shown.
Then the output of the Schmitt trigger is high, the clamp transistor TR; is conducting and the input current passing through R2 is shunted to ground. The current passing through R 1 causes a falling ramp to be formed. When the Schmitt circuit changes state, its output switches TR; to the nonconducting state. The current flowing through R2 can be made twice that flowing through Fl; (R2 = R;/2) so that the rising part of the ramp has a similar slope to the negative part.  The greater the value of the control voltage, the greater the frequency of oscillation. However,  the voltage must exceed the constant input voltage (V,) or the circuit will fail to oscillate. 


Read More..

Wednesday, September 24, 2014

High Voltage Generator Circuit Diagram

This is a short  High Voltage Generator Circuit Diagram of a high voltage generator and can be mounted in a small space and powered by rechargeable or simple batteries, the circuit generates a voltage low current but a high turn-on of about 200 to 400 V harmless to humans, of course, but is able to give a pretty nasty shock. 

 High Voltage Generator Circuit Diagram

 High Voltage Generator Circuit Diagram


Here is a project that could be useful this summer on the beach, to prevent anyone touching your things left on your beach towel while you was swimming, you can equally well use it in the office or workshop when you return to work. It operates as a low frequency oscillator, which makes it possible to convert the battery voltage into a DC voltage alternating current that can be enhanced through the transformer. 

Using a transformer with center tap as herein makes possible the construction of a Hartley oscillator transistor T1 around The output voltage can be used directly through R2 and R3 current limiting resistors, which should not in any circumstances be omitted or modified, they are what make the circuit have security. You will then get about 200 V peak-to-peak, which is already quite unpleasant to the touch. 

But you can also use a voltage doubler, shown at the bottom right of the figure, which will produce about 300 V, even more unpleasant to the touch. Here too, of course, the resistance, you know how R4 and R5, should always be present. It can be used in small electric fences, chase away animals, etc.
Read More..

DC Voltage Doubler using the 74HC132 Circuit Diagram

This circuit is a cheap way is a simple DC voltage doubler, which requires a few components and will generate a voltage 10Vdc from a 5Vdc power supply that can be output from the PC USB. The oscillator should be constructed from a non-functional door IC 74HC132 then requires more than two components are R1 and C3. The most important parameters of the voltage doubler circuit are given in the table schema.

Note 
That due to the tolerances of the data IC may have a few differences.


DC Voltage Doubler using the 74HC132 Circuit Diagram


Read More..

AC Mains Voltage Stabilizer Circuit

It will be easier to understand the operation of the circuit if we separate the under and over-voltage protection circuitry comprising transistors T1, T2 and associated components from the rest of the regulator circuit. Diode Dl arid. capacitor C2 provide 24V DC supply required to operate the relays.

Diode D2 and capacitor Cl provide the sample DC voltage for generating reference voltages for the cutout. For initial setting of cutout, collector of Tl is not connected to the base of T2. Also the time delay capacitor C4 is only connected after both under- and over- voltage points have been preset independently. Initially, due to the potential divider action of resistors R4, R6 and preset VR2, a voltage would appear at the base of T2. · lf this voltage is 0.6 ·V or more above the zener diode voltage of D4, transistor T2 would conduct, energising the relay and  connecting the hot tap of the auto-transformer to the universal socket’s hot terminal through N/O contacts of the relay RLl. _ Resistor R7 is for limiting base current. Therefore poten- tiometer VR2 is preset in a position where the relay would just switch off below the required lower trip point. On the sample prototype this was adjusted at l55V input, a value at which the output voltage of the regulator was 200V—the lower limit for our specified regulated output.

Whenever output voltage goes below this safe operating voltage, the relay releases and disconnects the power to the appliance and simultaneously gives a visible indication of this by applying power to the neon light through its N/ C contacts. At this point the collector of Tl is connected to the base of T2. Again a sample voltage would be available at the cathode  of D3 due to the potential divider action—of Rl, VR1 and R3. If this voltage exceeds the zener voltage of D3, transistor T1 would be able to conduct. This would clamp the base of T2 to ground. Since the base ofT2 has been pulled to ground, T2 would be no longer conductive and hence once again the cutout relay would be released, disconnecting the supply to the load. Preset VRl is so adjusted that as soon as the output supply voltage exceeds the upper limit (240·volts in our case), transistor T1 conducts and releases the relay. Once the over- and under-voltage points have been set, capacitor C4 (whose value may be found out experimentally) may be added between the base of T2 and ground.

This capacitor is essential to introduce a time lag in the operation of the cutout when rapid variations occur in mains supply. With capacitor C4 connected, the cutout waits till a steady level of voltage is reached. This also helps in avoiding erratic behaviour of the cutout.  Referring to only one section, say around T3 and T4, of our regulator circuitry, we find that transistor T3 would conduct when its base is at a negative potential as compared to its emitter. The emitter of T3 is fed with a fixed reference voltage from the anode of D5 which remains more or less constant over the input voltage range. Preset VR3 is adjusted to a point where, any further increase in the input voltage switches T3 on, and consequently T4,·pulling_ RL2 on. Further stages are similarly set at different voltages. Setting Having checked up the wiring, procure a variable auto- transformer (known as variac) to set the correct input-output voltage range.

 A very simple test for making sure that all stages of your circuit are operating is to feed input mains voltage and see that all the relays can be switched on or off by merely changing the settings of presets. At this stage no output load should be connected to the regulator. lf any part of the circuit remains permanently on or off, then the components as well as wiring for that particular stage may be checked thoroughly for faults. lf everything seems correct then connect a good quality multimeter, switched to read 250V AC, at the output socket. The cheap type of AC voltmeter mounted on the regulator panel is generally not a reliable instrument for accurate readings and should periodically be checked for calibration. Using a variac apply an input between 155 to 160 volts till you get an output just around 200 volts. Reduce this voltage slightly and make sure that as soon as it reaches below 200 volts (threshold between 195 and 200V) the low voltage cutout transistor T2 switches off, releasing RL1.  For this test, base of T2 should not be connected to collector of Tl, so also positive of C4,_ as described under the cutout section. At this point no voltage would be available at socket SOI and neon Ll would be lit. Increase and decrease this voltage at the threshold range a number of times to make sure the steady repeat accuracy of the cutout. Having set this, preset VR2 may be sealed with a blob of paint. Next keep on increasing the input volts till the output just reaches 240V our upper limit for regulated voltage.

Till this _ stage all the presets of the regulator must be so positioned that none of the relays is on. So far as the auto-transformer is concerned this would mean that the input hot line is connected to point 1 of the transformer with output at point 4. incidentally this is the maximum step-up given by the transformer for the lowest input range. As soon as output voltage tries to shoot beyond 240V, preset VR3 should be adjusted to switch on RL2. ` This would change the input hot end from point l to point 2 of X2, thus reducing the step·up ratio of X2. Keep on increasing the input voltage with variac till again it reaches 240V output. Now the relay RL3 should be adjusted with preset VR4 to switch on, further reducing the step-up ratio.


Read More..

Tuesday, September 16, 2014

Battery Low Voltage Beeper Circuit

Simple Battery Low Voltage Beeper schema provides an audible and visual low voltage warning for 12V battery powered devices. When the battery voltage is above the set point (typically 11V), the schema is idle. If the battery voltage should fall below the set point, the LED will light and the speaker will emit a periodic beeping sound to warn of the impending loss of power. The schema was designed for monitoring solar systems, but it could also be useful for automotive and other 12V applications.

Specifications:
  • Nominal operating voltage: 12V
  • Idle current: 6ma
  • Low Voltage Warning current: 15ma
Theory:
U2 provides a 5V regulated voltage reference. U1 is wired as a comparator, it compares the fixed 5V regulated voltage to the voltage on the wiper of VR1, that is proportional to the 12V supply. When the supply drops below the set point, the output of U1 goes low, turning on Q1 and powering the beeper and the LED.

The beeper consists of U4, a tone generator, and U3, a low duty cycle pulse generator. The tone can be changed by adjusting R7, the beep rate can be changed by adjusting R5. A small amount of hysteresis is provided by R1 and the current through LED1 and the beeper, this separates the on and off points for the schema.

Battery Low Voltage Beeper Circuit

Battery

Simple Battery Low Voltage Beeper schema board was made by printing the pattern (see below) onto Press-n-peel blue schema board transfer film with a laser printer. Etch the board, drill the holes, and assemble the parts on the board as per the board photo. Be sure to correctly orient the diode, electrolytic capacitors, ICs, and transistor. The CA3160 op-amp may be difficult to find, other low power CMOS op-amps may be substituted. A standard 741 op-amp would also work, but the idle current will be higher.

Alignment:
Connect the schema to an adjustable DC voltage source. Set the voltage source to 11V or wherever you would like the schema to turn on. Turn on switch S1. Adjust VR1 until the point where LED1 just comes on and the beeping starts.

Use:
Connect the schema to the 12V source that you wish to monitor. There should be a fuse somewhere between the battery and this schema. Turn S1 on, if the battery voltage is above the set point, nothing should happen.
As the battery voltage drops below the set point, the LED will light and a periodic beeping will come from the speaker. If the beeping becomes annoying, turn off S1. Be sure to charge the battery soon, excessive discharging will shorten the life of most rechargeable batteries.
Read More..

Tuesday, September 2, 2014

Simple Capacitor Discharge High Voltage Generator Wiring diagram Schematic

Simple Capacitor Discharge High Voltage Generator Circuit Diagram Stepdown transformer T1 drops the incoming line voltage to approximately 48 Vac which is rectified by diode D1; the resultant de charges capacitor C1-through current limiting resistor Rl-to a voltage level preset by R4. When the voltage on R4`s wiper reaches about 8.6 V, Q1 begins to turn on, drawing current through R7 and the base-emitter junction of Q2. 

Q2 turns on and supplies a positive voltage to the gate of silicon-controlled rectifier Q3. The positive gate voltage causes Q3 to conduct, thereby discharging C1 through the primary winding of step-up transformer T2, which results in a high-voltage arc at output terminal X. The voltage developed at T2`s output is determined by the value of C1, the voltage across C1, and the turns ratio of transformer T2. 

The frequency or pulse rate of the high voltage is determined by the resistance of T1 `s primary and secondary windings, the value of R1, and the value of Cl. The lower the value of each item, the higher the output pulse rate; the peak output voltage will only remain unchanged if C1`s value remains unchanged.

Capacitor Discharge High Voltage Generator Circuit Diagram

Capacitor

Read More..

Thursday, August 28, 2014

Basic single supply voltage regulator Wiring diagram Schematic

The schema uses a CA3140 BiMOS op amp capable of supplying a regulated output that can be adjusted from essentially 0 to 24 volts. The schema is fully regulated.

 Basic single-supply voltage regulator Circuit Diagram


Basic
Read More..

Friday, August 22, 2014

High And Low Voltage Cut Off With Time Delay Wiring diagram Schematics

The power line fluctuations and cut-offs cause damages to electrical appliances connected to the line. It is more serious in the case of domestic appliances like fridge and air conditioners. If a fridge is operated on low voltage, excessive current flows through the motor, which heats up, and get damaged.

The under/over voltage protection schema with time delay presented here is a low cost and reliable schema for protecting such equipments from damages. Whenever the power line is switched on it gets connected to the appliance only after a delay of a fixed time. If there is hi/low fluctuations beyond sets limits the appliance get disconnected. The system tries to connect the power back after the specific time delay, the delay being counted from the time of disconnection. If the power down time (time for which the voltage is beyond limits) is less than the delay time, the power resumes after the delay: If it is equal or more, then the power resumes directly.

This schema has been designed, built and evaluated by me to use as a protector for my home refrigerator. This is designed around readily available semi-conductor devices such as standard bipolar medium power NPN transistor (D313/SL100/C1061), an 8-pin type 741 op-amp and NE555 timer IC. Its salient feature is that no relay hunting is employed. This draw back is commonly found in the proctors available in the market.

The complete schema is consisting of various stages. They are: - Dual rail power supply, Reference voltage source, Voltage comparators for hi/low cut offs, Time delay stage and Relay driver stage. Lets now look at the step-by-step design details.

Dual rail power supply.
This is a conventional type of power supply as shown in Figure 1. The power is applied through the step-down transformer (230/12-0-12V/500mA). The DC proportional to the charging input voltage is obtained from bridge rectifier. Two electrolytics are there to bypass any spikes present. Bridge is capable of handling currents up to 1 Amp.
Output is given by: -
V(out) = 0.71 X V (secondary)
= 0.71 X 24V
= 17.04 V
(This equation is similar for the negative rail as well)

Circuit diagram

Build


Low voltage cut off op-amp
Figure 2 shows the use of very common and easily available op-amp 741 as a comparator. The op-amp is available in TO-5 and DIP type packing.

Circuit diagram

Build


In this ckt the zener diode D1 and it’s associated resistor R1 are connected to the non-inverting terminal (+ve) of 741 to give the suitable reference voltage. The DC voltage from the sensor is given to the inverting (-ve) terminal through pre-set R2.This is used to set the input level.
When the sensor input is less than Zener voltage the output from the Op-amp remains high and when it is greater than Zener voltage the output goes low. When the sensing voltage is equal to Zener voltage the output of the op-amp is approximately zero.
This phenomenon is used as a decision for switching the relay and to give cutoff in a low voltage situation.

High voltage cut off op-amp
Here the op-amp is used as a inverted amplifier. See Figure 3.Zener and resistor network gives reference voltage to the inverting terminal (-ve) of op-amp. Sensing voltage derived through the 10 K pre-set is given to the non- inverting (+ve) terminal and this sets the high level cut.

When the input DC from the sensor is less than Zener voltage the output of the op-amp is low and vice-versa. When the input DC voltage is equal to the zener voltage, the op-amps output is approximately zero.

Circuit diagram

Build


Time delay
I’ve selected the 555 timer due to following reasons.
1. Timing from microseconds through hours.
2. Ability to operate from wide range of supply voltages.
3. High temperature stability.
4. Easily Available.
5. Its triggering schema is quite sensitive.

This is basically a monostable. The external timing capacitor C2 is held initially discharged by the timer. The schema triggers upon receiving a pulse to its pin 2 when the level reaches 1/3 Vcc. Once triggered., the schema will remain in that state until the set time is elapsed or power to the schema cuts off. The delayed period in seconds is 1.1 C2.R1 where R1 is in megohms and C2 is in microfarads. In practice, R1 should not exceed 20 M. If you use an electrolytic capacitor for C2, select a unit for low leakage. The time delay may have to be adjusted by varying R1 to compensate for the wide tolerance of electrolytics.

Circuit diagram

Build


Relay Driver
The output from the voltage level detectors cannot directly drive the relay and hence the relay driver is used.

Circuit diagram

Build


In this a relay (12V <500 ohms) is connected to the collector of NPN transistor. The out put voltage from the comparator is applied to the base of NPN transistor through a resistance R1. When the output from the comparator is low the transistor is in OFF state and the relay is in de-energized state. Similarly when the output from the comparator goes high the transistor switches ON and the flow of current from the collector to emitter of transistor energizes the relay.

Generally in a relay driver schema, parallel to the relay coil, a diode or a capacitor is used. This is to eliminate the back e.m.f generated by the relay coil when currents are suddenly broken. Capacitor C1 is connected in parallel to the coil, which filters out the back emf but it, slows down the working of relay.

A better method is to connect two diodes (as shown in the figure 5) that stop the relay – transistor junction swinging more than 600mV above the positive rail or below the zero-volt rail. During normal operation the diodes are reverse biased and have no effect on the performance of schema. But when back emf is induced, the diodes conduct heavily and absorb all transient voltages. However, I have employed the both methods.
The Complete Circuit

Circuit diagram


Build


Under normal operating conditions i.e. when the input voltage is between maximum and minimum limit the output from the both the comparators are low. The transistor Q1 is OFF and the relay is in de-energized (pole connected to N/C pin) state and the output is obtained.

When the input voltage is below or above the limits set by the pre-sets R8 or R9, the output of the Op-Amps goes either low or high and diodes D1 or D2 would be forward biased depending on the situation. Transistor Q1 switches ON and the flow of current from collector to emitter energizes the relay and the output is cutoff.

A small amount of hystersis has been added via feed back resistors R10 & R11 so that the relay turns on when the level falls to a particular value but does not turn again until it raises a substantial amount above this value. Other wise the relay contacts will frequently turn on/off and produce chattering.

Construction Hints
1) I used a piece of varoboard, which has copper strips on one side to mount the components, and housed the entire schema and the transformer in a discarded ATX PC power supply box.

2) An autotransformer has been used to set the limits. Set the output of the autotransformer to 250V AC and connect it to the primary of transformer T1 (see Figure 1). Then adjust the pre-set R9 such that relay just energizes. This is the high limit. Next set the output of the autotransformer to 200V AC and adjust the pre-set R8 such that the relay energizes. Please note that these are my preferred limits but you may select any range from say 170 to 270V AC.

3) A neon with a suitable resistor could be connected between the AC supply lines as an ON indicator. Alternatively, LED with a current limiting resistor could be connected between the relay coil so when the relay is energized LED will indicate the situation.
Read More..

Low Power Voltage Reference Wiring diagram Schematic

The Low Power Voltage Reference Circuit Diagram described below, is a special implementation of current source LM334. Characterized by a very small temperature coefficient metatholio output voltage and consumes only 10uA room temperature. This current fluctuates by a few uA, when the ambient temperature varies significantly. The positive rate of temperature change LM334 offset by the negative of the contact base emitter transistors has a direct thermal coupling with the integrated. 

To achieve the lowest possible temperature coefficient, it is necessary to adjust the output voltage of 1,253 V source to the arrangement easily done through R1. From the moment you get the desired output voltage, you are advised to stuck P1 and after the count value, replace it with a constant resistance. The best indeed is to replace P1 with the R1, so you have fewer parts. Prefer metal film resistors and tolerance of 1% E96 series. Having as a given that the output voltage obtained from the pin configuration LM334, is expected to show a negative resistance value 3.8 KO. 

The resistance A3 ensures that the output impedance will be equal to 400 W. Under these conditions, the current that can provide the source to the load to be connected to out of retained less than 5 Ma stability of the voltage source is more than satisfactory. By varying the input voltage from 5 V to 30 V, the change in output was only 0.6 mem (from 1.2530 to 1,2536 V). The change in the thermal coefficient is maintained at values ??less than 50 ppm / C, and if you worry a bit more to the setting of the schema, you will see that quite easily reaches 5 ppm / C. The requirements of the original schema current was only 9.8 mA at a temperature of 22C.

Low Power Voltage Reference Circuit Diagram

Low

Read More..

High Low voltage cut off with delay alarm



This straight forward schema will protect electrical appliances from over voltage as well as under voltage.The schema also produces an alarm when the power supply comes back.An ideal schema for home to protect your valuable equipments from voltage fluctuations.The same schema with some modifications can be used to make a automatic voltage stabilizer








When the mains voltage is in the normal level ,the voltage at the negative terminal of zener diode D4 will be less than 5.6 Volts.At this condition transistor T1 will not conduct.The same time voltage at the negative terminal of zener diode D5 will be greater than 5.6 and so the transistor T2 will be conducting.The relay will be activated and the green LED wil be glowing.

When the mains voltage is higher than the set limit the transistor T1 becomes conducting since the voltage at the negative terminal of D4 is greater than 5.6 V.At the same time transistor T2 will be non conducting which results in the deactivation of relay to cut the mains supply from load.When the mains voltage is less than the set limit transistors T1 & T2 becomes non conducting making the relay to de- activate and cut the load from mains.Ω

The timer NE555 is wired as a monostable multivibrator with a pulse width of 10ms.When the power comes back after a cut off a negative voltage is obtained at the trigger pin which triggers the IC NE555.The transistor T3 gets forward biased and it drives the buzzer to produce a beep as an indication of power resumption.Also the transistor T1 is made on which in turn makes T2 off.As a result the relay will remain de- activate for 10ms and this provides the sufficient delay and the equipment is protected from surge voltages.




Notes.

* To calibrate the schema a autotransformer is needed.Connect the output of autotransformer to the transformer primary.
* Set the voltage to 260V and adjust VR1 to make the relay deactivated.
* Now set the autotransformer to 160V and adjust VR2 so that the relay is de-energized.
* VR3 can be used to vary the volume of buzzer.


Read More..

Sunday, August 17, 2014

7805 Voltage Regulator Wiring diagram Schematic

A voltage regulator is used to produce a constant linear output voltage. It’s generally used with AC to DC power supply. And also it can be used as well as a DC to DC voltage converter . To regulating low voltage, most used device is one single IC. 7805, 7812, 7905 etc. 78xx series are design for positive and 79xx series are for Negative voltage regulator.

7805 is a three terminal +5v voltage regulator IC from 78XX chips family. See 7805 pinout below. LM78XX series are from National Semiconductor. They are linear positive voltage regulator IC; used to produce a fixed linear stable output voltage.  National Semiconductor has also negative voltage regulator chips family, they indicate with LM 79XX. 78xx is used more than 79xx because negative voltage has a few usability purposes as we see.

I was previously posted a 5v regulated power supply schema using 7805 IC, that schema and this 7805 voltage regulator schema is almost the same.


7805 Voltage Regulator Circuit Diagram

 
7805
Its output voltage is +5V DC that we need. You can supply any voltage in input; the output voltage will be always regulated +5V. But my recommendation is, don’t supply more than 18V or less than 8V in input. There used two capacitors in this voltage regulator schema, they aren’t mandatory to use. But it will be best if you use them. They helped to produce a smooth regulated voltage at output. Use electrolyte capacitor instead of ceramic capacitor.

One limitation of 7805 I have found that is its output current 1A maximum. Otherwise it is a good voltage regulator if you are happy with 1A. But if   you need over 400mA current in output then you should use a Heat Sink with IC LM7805. Otherwise it may fall damage for overheating.Link
Read More..

Thursday, August 14, 2014

Universal battery charger with 12V source voltage

phone battery charger with 12V source  voltage
In this post I will share about using Accu source to charge batteries that can be used on any mobile brand, or can be called universal phone battery charger. Because the battery charger using a source of 12V, the charge accumulator can also be used in cars and others.

Read more
Read More..

Monday, August 11, 2014

Car Voltage Gauge

The Car Voltage Gauge is based on 3 parts. The input schema is an Analog to Digital Converter (IC2 CA3162E). The purpose of this chip is to sample an analog voltage and convert it to a decimal value which is read by a Display/Decoder Driver (IC1 CA3161E). This chip will turn each seven segment display on through the driver transistor Q1 - Q3. The power is derived from the car and is converted to 5 volts by the 5 volt regulator. The schema works as follows: The 10uf capacitor is charged up by the cars voltage. Its value is then read by IC2 and a decimal value of that voltage is provided to IC1 which multiplexes the three display units.

Car Voltage Gauge schema diagram

Each display is turned on sequentially with its appropriate value displayed. The transistors Q1 through Q3 control the drive to each seven segment display. By monitoring the cars voltage with an accurate multimeter you can adjust the "Zero Adj." pot and the "Gain Adj." pot for accurate readings. LED 1 and 2 are optional. They can be used to indicate power on or can light up a cut out display that says "Volts". This can be made by a plastic module that has a thin plastic cover on it with the word "Volts" cut into it. The LEDs would be mounted inside the module. 
Source by : www.diagramproject.com
Read More..